Autodesk Certified Professional in Design for Manufacturing with Autodesk Fusion Exam Prep
Free practice questions

Free ACP Practice Questions

10 exam-style questions with answers and explanations, straight from our 1,030-question bank. Tap an answer to check yourself. When you're ready, take the scored version in the free practice test.

Start the free practice test → ★★★★★4.9/5 from 2,400+ candidates · No signup

The ACP exam has 60 questions and runs 2 hours.

These 10 free ACP questions are organized by exam domain, so you can see how each part of the Autodesk Certified Professional in Design for Manufacturing with Autodesk Fusion blueprint is tested. Reveal the answer and explanation under each question.

Domain 1: Manufacturing design rules

Question 1

'The cutter fits every internal radius, so this seat is machinable.' A reviewer finds that a solid lip blocks every straight tool approach to the recessed seat along the setup's axis. Cutting length is adequate. The job permits one fixed-orientation three-axis setup with standard cylindrical end mills; redesigning the lip is allowed. Which proposal resolves the review finding?

Show answer & explanation

Correct answer: A - Remove the overhanging portion of the lip to provide access along the existing tool axis.

Question 2

A Draft Analysis referenced to +Z reports +3.5 degrees on one mold half's release walls and -3.0 degrees on the other half's walls. The halves withdraw in +Z and -Z, respectively. Each wall set requires at least 2 degrees of positive draft relative to its own withdrawal direction, and there are no other withdrawal obstructions. What is the correct disposition of the two wall sets?

Show answer & explanation

Correct answer: D - Accept both sets; each has sufficient positive draft in its own withdrawal direction.

Domain 2: 3D component modeling

Question 3

A plate grows symmetrically about a fixed vertical construction line, but two holes dimensioned from its left edge drift off center when the plate widens. Their diameters and common height are already constrained. The designer will replace only their horizontal positioning dimensions. Which arrangement keeps the pair centered while making its center spacing respond to the user parameter HolePitch?

Show answer & explanation

Correct answer: C - Apply Symmetry to the hole centers about the construction line, then drive their separation with HolePitch.

Question 4

In a parametric housing, a rectangular boss starts on an interior base face and must end flush with an existing sloped roof face. The roof is created earlier in the timeline and may change both height and slope. The boss's footprint will remain beneath that face. Which revision to the boss extrusion makes its end follow the roof?

Show answer & explanation

Correct answer: B - Choose To Object, select the roof face, and set the termination offset to zero.

Question 5

After applying Tangent between a spline and an adjoining circular arc, a designer confirms that the endpoints and tangent directions match. The rate at which the profile turns still changes abruptly at the join. The arc's radius must remain fixed, and the styling requirement is G2 continuity. What sketch change addresses the remaining requirement?

Show answer & explanation

Correct answer: A - Replace the tangent-only condition with a Curvature constraint at the join.

Question 6

A closed-ended slot is specified in a sheet-metal blank. It crosses a region that will become a 90-degree bend, with one end on each flange after forming. An engineer creates the cut in Flat Pattern: it appears in the DXF but not in the folded design. The formed opening is needed for assembly clearance checks. Select the workflow that creates this blank-normal cut in the design and preserves it after forming.

Show answer & explanation

Correct answer: B - Use Unfold, create the slot in the design, Refold, then update and reexport the flat pattern.

Domain 3: 3D assembly modeling and management

Question 7

An adjustment shaft is already positioned correctly inside a grounded housing. It must rotate freely about its own axis and slide through an 18 mm axial travel, with no fixed relationship between rotation and translation. No other joints act on the shaft. Which single relationship preserves its placement and represents the required motion?

Show answer & explanation

Correct answer: D - An As-Built Cylindrical joint, with limits on axial travel.

Question 8

A cover component contains one solid body. Its volume and units match the approved geometry. The component's material label reads Aluminum, but its calculated mass still matches the previous steel version. Applying an aluminum appearance has not changed that mass. The measurement includes only this body. Where should the designer look before altering the part geometry?

Show answer & explanation

Correct answer: A - The body's effective physical material and any retained material override.

Domain 4: Create exploded view animations

Question 9

An exploded-view storyboard moves a retaining plate from 1 to 3 seconds and a trapped cartridge from 2 to 5 seconds. The cartridge cannot begin moving until the plate reaches its final exploded position. The cartridge's path, displacement, and three-second travel time are already correct. To repair the sequence while retaining the plate's approved timing, the animator should:

Show answer & explanation

Correct answer: D - Move the unchanged cartridge action to the interval from 3 to 6 seconds.

Domain 5: Technical detailed drawing creation

Question 10

A drawing specifies a hole diameter of 10.00-10.20 mm and a position tolerance of diameter 0.10 mm at maximum material condition, relative to datums A, B, and C. The hole is verified cylindrical and measures 10.12 mm. Inspection in the specified datum reference frame, with no datum shift, reports a diametrical position error of 0.18 mm. All other requirements are satisfied. What disposition follows from the size and position controls?

Show answer & explanation

Correct answer: C - Accept the hole: the measured size increases its allowable position tolerance to diameter 0.22 mm.

The rest of the ACP blueprint

The ACP exam also covers these domains. Drill them in the full free practice test:

That's 10 of 1,030

The full bank has 1,020 more ACP questions with explanations.

Continue in the free practice test →

View plans